I have a very short equipment rack installed in my server closet. It is only 16 inches deep, fine for most networking uses, but not great for most rack-mount server cases.
I am looking for case suggestions that would fit my rack, 16 inch depth maximum. Height isn’t a problem, the rack has a ton of vertical space, over 15U, it’s the depth that’s an issue.
Thanks!
You must log in or register to comment.
I’ve looked all over the Internet for <16" short-depth cases multiple times over the years, and I’ve learned the most important question is this: what do you want to put in it?
I’ll tell you right now that some of the things I’ve wanted, like…
-
A 2U with hot-swap caddies all the way across the front (like this or this, but <16" deep at the cost of fitting only an ITX motherboard), or
-
A 4- or 5U chassis that can fit an EATX / SSI EEB (12"x13") motherboard and an ATX PSU at the same time, or
-
A chassis of any size that has both the motherboard/PCI I/O and the drive bays on the front (front drive bays are normal and you can get front access I/O, but not both at the same time)
…simply do not exist, as far as I can tell. I’m pretty sure all of these things are geometrically possible (I did the math), but apparently I’m the only one who wants such weird stuff.
You can get a basic-bitch whatever-U case that supports a mATX motherboard and hard-mounting a couple of internal drives, with sharp metal edges, a shitty plastic door, and a price double (or more) what similarly low quality would cost in a desktop form-factor all day long, though.
Yeah, seems like there isn’t a big group of folks that are looking for this kind of solution.
I’ve thought about designing a case to my specs that could be 3D printed or maybe be built with some very basic steel sheet, but that’s more DIY than I have time for right now.
-
deleted by creator
Thanks for the link!
These guys do short depth PCs. I wish I knew where they got their cases from, because they are really nice!
But I haven’t found anything decent in the wild (I eventually gave up and got a deeper rack so I can use old r730 servers)Thanks for the link! Yeah, I’m starting to think I might just need to give up and get a deeper floor rack.
There are some good short chassis like the Silverstone RM-23-502-MINI, but the minimum length for the recommended rails is still 22 inches :(
Chenbro makes quite a few ATX shallow rack mount cases. I have one and have no complaints.
I’ll check them, Ty!
https://www.amazon.com/gp/aw/d/B09227RQV2?psc=1&ref=ppx_pop_mob_b_asin_title
This is my favorite rack mount chassis I’ve worked with … and it coincidentally is in that ballpark.
Interesting design, I’ll look at it, thanks!
I’ve not used them yet but was looking at https://www.plinkusa.net/
They have a variety of heights and depths, some of them being 15”
Great resource, I’ll check them out.
Sliger has a few rackmount chassis which are only 15 inches deep.
Oh nice, these might be exactly what I need, thanks!
I recently hunted for a rack mounted case for an ATX MB and PSU. The best I could find is 17.9" deep. Is your rack’s rear end closed? Any way to remove the rear panel? There is a site that’ll make you a custom rack mount case I came across. But it was mighty pricey.
Back end is open but wall-mounted. If there is a way to mount the case forward a few inches so it leaves a gap in the back, that would be fine with me.
I haven’t found any brackets that seem to do that though.
How about mounting the rack a few inches off the wall?
Make your own brackets with construction lumber or plywood?
The 45Drives homelab case is 17.125" deep
Also an option I am considering. I prefer something a little more professional if possible, but not a bad option if I can’t get something else to work.
I’ll take a look at the 45 Drives case, thanks!
